Journal

Journal

113.  G. Roh, H. Kim, C. Kim, D. Kim, and B. Kang, “Fast and accurate method of lifetime estimation for HfSiON/SiO2 dielectric n-MOSFETs under positive bias temperature instability” Microelectron. Reliab. 72 (2017) 98-102.

112.  Hyeon-Seok Lee, Hyung-Jin Choe, Seok-Hyung Ham, and Bongkoo Kang, “high efficiency assymetric forward flyback converter for wide output power range” IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 32, NO. 1, JANUARY (2017)

111.  Donghee Son, Gang-Jun Kim, Ji-Hoon Seo, Nam-Hyun Lee, YongHa Kang, Bongkoo Kang, “Channel width dependence of AC stress on bulk nMOSFETs” Microelectronics Reliability 64 (2016) 194–198

110.  Ji-Hoon Seo, Gang-Jun Kim, Donghee Son, Nam-Hyun Lee and Bongkoo Kang, “Method of estimating mechanical stress on Si body of MOSFET using drain-body junction current” Japanese Journal of Applied Physics, Volume xx, Number xx

109.  Ji-Hoon Seo, Gang-Jun Kim, Donghee Son, Nam-Hyun Lee, Yongha Kang and Bongkoo Kang, “Method to predict length dependency of negative bias temperature instability degradation in p-MOSFETs” Japanese Journal of Applied Physics, Volume 55, Number 8S2

108.  Donghee Son, Gang-Jun Kim, Ji-Hoon Seo, Nam-Hyun Lee, YongHa Kang, Bongkoo Kang, “Degradation of pMOSFETs due to hot electron induced punchthrough,” Microelectronics Reliability 59 (2016) 13–17, January (2016)

107.  Active Balancing of Li-ion Battery Cells Using Transformer as Energy Carrier, Kyung-Min Lee, Sang-Won Lee, Yoon-Geol Choi, and Bongkoo Kang, IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, vol. 64, no. 2, pp 1251-1257

106.  Kyung-Min Lee, Yoo-Chae Chung, Chang-Hyeon Sung, and Bongkoo Kang, “Active Cell Balancing of Li-Ion Batteries Using LC Series Resonant Circuit,” IEEE Trans. Ind. Electron., vol. 62, no. 9, pp. 5491-5501, September (2015)

105.  Yoo-Chae Chung, Kyung-Min Lee, Hyung-Jin Choe, Chang-Hyeon Sung and Bongkoo Kang ” Low Cost Drive Circuit for AC-Direct LED Lamps” Power Electronics, IEEE Transactions on  Volume:30, Issue: 10, pp. 5776-5782, October (2015)

104.  Cheolgyu Kim, Hyeokjin Kim, Bongkoo Kang “Voltage dependent degradation of HfSiON/SiO2 nMOSFETs under positive bias temperature instability”, Microelectronics Reliability, Volume 54, Issue 11, November (2014), Pages 2383–2387

103.  Cheolgyu Kim, Hyeokjin Kim, Seonhaeng Lee, Jeongsoo Park and Bongkoo Kang, ” Saturation of threshold-voltage shift during positive bias temperature instability in HfSiON/SiO2 n-channel MOSFET and its effect on device lifetime evaluation” Japanese Journal of Applied Physics 53 (2014)

102.  Gang-Jun Kim, Ji-Hoon Seo, Donghee Son, Nam-Hyun Lee, YoungHa Kang, YuChul Hwang, and Bongkoo Kang, “Effect of dynamic stress on OFF leakage of small-dimension pMOSFETs at high temperature” , Japanese Journal of Applied Physics 53, (2014)

101.  Hyung-Jin Choe, Yoo-Chae Chung, Chang-Hyeon Sung, Jae-Jung Yun, and Bongkoo Kang, “Passive Snubber for Reducing Switching-Power Losses of IGBT in DC-DC Boost Converter”, Power electronics 29, pp. 6332 – 6341 (2014)

100. Yoochae Chung, Chang-Hyeon Sung, Jin-Ho Kim, Seung-Min Chae, Myung-Je Jeon, Bongkoo Kang, “Power-efficient drive circuit for plasma display panel”, DIsplays 35, 66-73 (2014)

99.  H. W. Lim, C. H. Baek, B.K.Kang, “Design of emitter ledge for thermal stability of AlGaAs/GaAs heterojunction” , Solid-State Electronics 81 , pp. 5-7 (2013)

98.  Seonhaeng Lee, Cheolgyu Kim, Hyeokjin Kim, Gang-Jun Kim, Ji-Hoon Seo, Donghee Son, Bongkoo Kang, “Effect of negative bias temperature instability induced by a low stress voltage on nanoscale high-k/metal gate pMOSFETs” , Microelectronic Reliability 53 , pp. 1351-1354 (2013)

97.  CheolGyu Kim, Nam-Hyun Lee, Young-Kyu Kwon , Bongkoo Kang, “Effects of film thickness and Sn concentration on electrical properties of solution-processed zinc tin oxide thin film transistors, Thin Solid Films” , Thin Solid Films 544, pp. 129-133 (2013)

96.  N.H. Lee, H. Kim, and B.K. kang, “Impact of OFF-State Stress and Negative Bias Temperature Instability on Degradation of Nanoscale pMOSFET”, Electron Device Letters 33(2), pp. 137-139 (2012) [pdf]

95.  Nam-Hyun Lee, Kang-Jun Kim, Hyung-Wook Kim, and Bong-Koo Kang, “Impact of OFF-state Degradation under Dynamic Stress on Reliability of Nanoscale n-Channel Metal-Oxide-Semiconductor Field-Effect Transistors at Elevated Temperature”, Jpn. J. Appl. Phys. 51(2), 02BC13, pp. 1-4 (2012) [pdf]

94.  Dongwoo Kim, Seonhaeng Lee, Cheolgyu Kim, Tae-Kyung Oh, and Bongkoo Kang, “The Effect of La2O3 Capping Layer Thickness on Hot Carrier Degradation of n-MOSFETs with High-k/Metal Gate Stack”, Jpn. J. Appl. Phys. 51(2), 02BC10, pp. 1-3 (2012) [pdf]

93.  M.S. Song, E.S. Oh, and B.K. Kang, “Modified SEPIC having enhanced power conversion efficiency”, Electronics Letters 48(18), 30th August (2012) [pdf]

92.  Dongwoo Kim, Seonhang Lee, Cheolgyu Kim, Chilho Lee, Jeonsoo Park, and Bongkoo Kang, “Enhanced degradation of n-MOSFETs with high-k/metal gate stacks under channel hot-carrier/gate-induced drain leakage alternating stress”, Microelectronics Reliability 52, pp. 1901-1904 (2012) [pdf]

91.  Seonhang Lee, Dongwoo Kim, Cheolgyu Kim, Chilho Lee, Jeonsoo Park, and Bongkoo Kang, “Channel width dependence of mechanical stress effects induced by shallow trench isolation on device performance of nanoscale nMOSFETs”, Microelectronics Reliability 52, pp. 1949-1952 (2012)[pdf]

90.  Seonhang Lee, Dongwoo Kim, Cheolgyu Kim, Chilho Lee, Jeonsoo Park, and Bongkoo Kang, “Effect of electron-electron scattering at an elevated temperature on device lifetime of nanoscale nMOSFETs”, Microelectronics Reliability 52, pp. 1905-1908 (2012) [pdf]

89.  Jae-Jung Yun, Hyung-Jin Choe, Young-Ho Hwang, Youg-Kyu Park, and Bongkoo Kang “Improvement of Power-Conversion Efficiency of a DC-DC Boost Converter Using a Passive Snubber Circuit”  IEEE Transactions on Industrial Electronics 59(4) (2012) 1808-1814 [pdf]

88.  Nam-Hyun Lee, Hyungwook Kim, and Bongkoo Kang “Impact of Off-State Stress and Negative Bias Temperature Instability on Degradation of Nanoscale pMOSFET”IEEE Electron Device Letter 33(2) (2012) 137-139 [pdf]

87.  Seonhaeng Lee Dongwoo Kim Cheolgyu Kim T.K. Oh S.Y. Cha S.J. Hong Bongkoo Kang “Measurement of mechanical stresses induced by hybrid shallow-trench-isolation for dynamic random access memory using recess channel array transistor structure”  Microelectronic Engineering 91 (2012) 44-49 [pdf]

86.  C.H. Sung, J.H. Kim, Y.C. Chung, M.J. Jeon J.W. Seo Y.K. Jung B.K. Kang “Biased scan of plasma display panel for data voltage reduction” Display33 (2012) 21-27 [pdf]

85.  Nam-Hyun Lee, Dohyun Baek, and Bongkoo Kang “Effect of OFF-State Stress and Drain Relaxation Voltage on Degradation of a Nanoscale nMOSFET at High Temperature” IEEE Electron Device Letter 32(7) (2011) 856-858 [pdf]

84.  Jae Joong Yun, Min Sup Song, Young Ho Hwang Bongkoo Kang “Method of controlling external electrode fluorescent lamps for local dimming of liquid crystal displays” Displays32 (2011) 142-149 [pdf]

83.  Dongwoo Kim Seonhaeng Lee T.K. Oh S.Y. Cha S.J. Hong Bongkoo Kang “Influence of dummy active patterns on mechanical stress induced by spin-on-glass-filled shallow trench isolation in n-MOSFETs” Microelectronic Engineering88 (2011) 882-887 [pdf]

82.  Min Sup Song Yong Kyu Park   Jae Joong Yun Young Ho Hwang Bongkoo Kang    “Distributed circuit model for cold cathode fluorescent lamps in back-light unit of liquid crystal display”  Display31 (2010) 114-110 [pdf]

81.  J.H. Kim, M.J. Jeon, G.H. Hur, K.S. Lee J.S. Kim B.K. Kang, “Bipolar drive waveform for long-gap high-Xe plasma display panels” Displays 31(2010) 67-72 [pdf]

80.  G.H. Huh, S.C. Lee, M.J. Jeon, J.H. Kim, B.K. Kang, “Floating single sustain drive method for AC plasma display panel” Displays 30 (2009) 32-38 [pdf]

79.  Nam-Hyun Lee, Hwan-Wook Choi, Heesung Kang, and Bongkoo Kang, “Experimental Method to Extract Effective Channel Length of Nanoscale n-MOSFETs” IEEE ELECTRON DEVICE LETTERS, VOL. 30, NO. 11, NOVEMBER (2009) [pdf]

78.  M.J. Jeon, J.W. Seo, S.Y. Soh, S.H. Kim, J.G. Han 1, B.K. Kang “Influence of wall charge distribution on time lag of address discharge in AC plasma display panels” Displays 29 (2009) 195-201 [pdf]

77.  H.W. Choi, N.H. Lee, H.S. Kang 1, B.K. Kang “Method of extracting effective channel length for nano-scale n-MOSFETs” Solid-State Electronics 53 (2009) 1076-1085 [pdf]

76.  Y.D. Kim, S.U. Han, H.S. Kang 1, B.K. Kang “Recovery of negative bias temperature instability induced degradation of p-MOSFETs with SiON gate dielectric” Microelectronic Engineering 85 (2008) 1932-1936 [pdf]

75.  J.H. Do, H.S. Kang , B.K.Kang “Electrical method of measuring physical thickness and nitrogen concentration of silicon oxynitride gate dielectric for MOSFETs” Microelectronic Engineering 85 (2008) 1820-1825[pdf]

74.  S.Y. Soh, M.J. Jeon and B.K. Kang “Electrical equivalent circuit for AC plasma display panels” IEEE Trans. on Plasma Science 35(5), pp. 1527-1532 (2007) [pdf]

73.  M.S.Chung, M.J.Jeon, S.C.Lee, B.K.Kang, H.J.Kim, S.S.Yang, J.S.Kim, Y.J.Ahn, “Effect of single crystalline MgO powder treatment of phosphor surface on discharge property of high-Xe AC plasma display panels”, Displays 28 pp. 68-73 (2007) [pdf]

72.  M.S.Chung, S.H.Kim, M.J.Jeon, B.K.Kang, “Improvement of picture quality of high Xe content plasma display panels based on facing discharge suppression”, Displays 28 pp. 74-80 (2007) [pdf]

71.  Development of beam profile monitor for cyclotron MC50, K.H. Park, Y.G. Jung, D.E. Kim, W.W. Lee, S.M. Hong, B.K. Kang, J.S. Chai, and D.H. Ahn, J. Kor. Phy. Soc. 50(4) pp.983-987(2007) [pdf]

70.  A new method of field measurement for solenoid magnet, K.H. Park, Y.G. Jung, D.E. Kim, H.G. Lee, S.J. Park, C.H. Chung, and B.K. Kang, J. Kor. Phy. Soc. 50(4), pp. 950-954 (2007) [pdf]

69.  Design of 6~18GHz wideband phase shifter using radial stubs, H.J. Kwon and B.K. Kang, IEEE Microwave and Wireless Components Letters 17(3), pp. 205-207 (2007) [pdf]

68.  A quantum-splitting phosphor exploiting the energy transfer from anion extitons to Tn3+ in CaSO4:Tb, Na, A. Lakshmanan, S.B. Kim, H.M. Jang, B.G. Kum, B.K. Kang, S. Heo and D. Seo, Advanced Functional Materials 17, pp. 212-218 (2007) [pdf]

67.  S.C.Lee, S,Y,Soh, J,W,Seo, and B,K, Kang, “Versatile energy recovery circuit for driving AC plasma display panel with single sustain circuit board”, Displays 27 pp. 153-160 (2006) [pdf]

66.  Cell parameter extraction method for AC plasma dispay panels, S.Y.Soh, S.H. Kim, J.W. Seo, Y.K. Jung and B.K. Kang, Displays 27 pp.97-107 (2006) [pdf]

65.  Magnetic block measurement for insertion device in PAL, K.H. Park, D.E. Kim, H.S. Suh, H.G. Lee, W.W. Lee, Y.G. Jung, H.S. Han, C.W. Chung, and B.K. Kang, J. Kor. Phys. Soc. 48(4), pp. 763-767 (2006)

64.  Rare earth doped CaSO4 luminescence phosphors for applications in novel displays – new recipes, A. Lakshmanan, S.B. Kim, B.G. Kum, H.M. Jang, and B.K. Kang, Phys. Stat. Sol. A 203(3), pp. 565-577 (2006)

63.  Time-dependent degradation due to negative bias temperature instability of p-MOSFET with an ultra-thin SiON gate dielectric, S. U. Han, H. S. Kang, B. K. Kang, Microelectronic Engineering 83(3), pp.520-527 (2006) [pdf]

62.  Effect of plasma process-induced damage on bias temperature instability of MOSFETs, T. S. Jang, M. H. Ha, K. D. Yoo, B. K. Kang, Microelectronic Engineering 83(3), pp.415-422 (2006) [pdf]

61.  Effect of surface treatment onthe electrical properties of AlGaAs/GaAs heterostructure bipolar transistor, C. H. Baek, T. K. Oh, and B. K. Kang, Solid-State Electronics, Vol.48(8), pp.1335-1340 (2005) [pdf]

60.  Linear Frequency Modulation of Voltage-Controlled Oscillator using Delay-Line Feedback, H. J. Kwon and B. K. Kang, IEEE Microwave and Wireless Components Letters 15(6), pp. 431-433 (2005) [pdf]

59.  Field mapping system forcyclotron magnet, K. H. Park, Y. G. Jung, D. E. Kim, B. K. Kang, M. Yoon, S. Chai, and Y. S. Kim, Nucl. Instr. and Meth. A, Vol.545(3), pp.533-541 (2005) [pdf]

58.  A drive waveform for high resolution and high Xe content AC plasma display panels, S. H. Kim, J. W. Seo, S. Y. Soh, Y. K. Jung, J. Y. Kim, B. K. Kang, Displays 26, pp. 45–53 (2005) [pdf]

57.  Twin voltage-ramp reset for high speed addressing of three-electrode AC plasma display panel, J. W. Seo, S. H. Kim, S. Y. Soh, J. Y. Kim, J. H. Ryu, and B. K. Kang, Displays 25(2), pp.49-56 (2004) [pdf]

56.  Surface treatment for enhancing current gain of AlGaAs/GaAs heterojunction bipolar transistor, T. K. Oh, C. H. Baek, and B. K. Kang, Solid-State Electronics 48(9), pp.1549-1553 (2004) [pdf]

55.  Plasma process induced damages on n-MOSFET with plasma oxidized and nitrided gate dielectrics, T. S. Jang, M. H. Ma, K. D. Yoo, and B. K. Kang, Microelectronic Engineering 75(4), pp.443-452 (2004) [pdf]

54.  Fabricationof Hyperboloid-Drum Structure for Electro-Pumped Laser with Sub-micron toNanometer Size Emitter, J.Y. Kim, S.J. An, J.Y. Kim, J.W. Lee, B.K. Kang, and O’D. Kwon, J. Vac. Sci. &Technol. B 22(2), pp.673-677 (2004) [pdf]

53.  Enhancement of Physical and Chemical Properties of Thin Film Ag/AgCl Reference Electrode using Ni Buffer Layer, H. R. Kim, Y. D. Kim, J. H. Shim, H. Nam, and B. K. Kang, Sensors and Actuator B 97(2), pp. 348-354 (2004) [pdf]

52.  Pulsed wire magnetic field measurement of MPW14 at PLS, K. H. Park, S. H. Jeong, D. E. Kim, W. W. Lee, C. W. Chung, and B. K. Kang, Surface, X-ray, Synchrotron and Neutron Investigations, No. 11, pp. 107-109 (2003)

51.  Effect of surface treatment on leakage current of GaAs/AlGaAs laser microcavities, J. Y. Kim, J. W. Lee, J. Kim, B. K. Kang, and O’D. Kwon, Appl. Phys. Lett. 82(25), pp. 4504-4506 (2003)

50.  Circuit model for two-electrode AC discharge, Y. K. Jung, J.W. Seo, Y.H. Kim, B.K. Kang, IEEE trans. on Plasma Science 31(3), pp. 362-368 (2003)

49.  Size and Interface State Dependence of the Luminescence Properties in Si NanoCrystals, C.G. Ahn, T.S. Jang, K.H. Kim, Y.K. Kwon,, B.K. Kang, Jpn. J. Appl. Phys 42(4B) pp. 2382-2386 (2003)

48.  Modified Wilkinson Power Divider for nth Harmonic Suppression, K. H. Yi, B.K. Kang,Microwave and Wireless Components Letter 13(5), pp.178-180 (2003)

47.  Laminated Magnetic Flux Sensor for Thick Steel Plate Control, K.H.Park, D.E. Kim, S.H. Jeong, and B.K. Kang, IEEE Trans. on Industrial Electronics 50(2), pp. 379-384 (2003)

46.  Scan-During-Sustain Method for Driving High Resolution AC Plasma Display Panel, S. J. Yoon, B. K. Kang, N. K. Lee, and Y. H. Kim, International Journal of Electronics 89(4), pp. 289-304 (2002)

45.  Scan-During-Sustain Method for Driving High Resolution AC Plasma Display Panel, S. J. Yoon, B. K. Kang, N. K. Lee, and Y. H. Kim, International Journal of Electronics 89(4), pp. 289-304 (2002)

44.  S. J. Yoon, Y. K. Jung, J. W. Seo, B. H. Lee, Y. H. Kim, and B. K. Kang, “Selective Charge-Inversion Addressing Method for Driving AC Plasma Display Panel”, Display 23(4), pp. 19-26 (2002)

43.  T. K. Oh, J. G. Lee, K. H. Yi, C. H. Baek, B. U. Ihm, and B. K. Kang, “Properties of AlGaAs/GaAs Heterojunction Bipolar Transistor with AlGaAs Ledge Bypass Capacitor”, Solid-State Electronics, Vol.46(1), pp.35-38 (2002)

42.  M. S. Hur, J. K. Lee, H. C. Kim, and B. K. Kang, “The Effective Secondary Electron Emission Coefficient in Plasma Display Panel”, IEEE Trans. on Plasma Science, Vol.29(5),pp.861-863 (2001)

41.  B. K. Kang, J. C. Park, and Y. H. Kim, “Plasma Uniformity of Inductively Coupled Plasma Reactor with Helical Heating Coil”, IEEE Trans. on Plasma Science, Vol.29(2), pp.383-387 (2001)

40.  J. Y. Kim, K. S. Kwak, J. S. Kim, B. K. Kang, and O’D Kwon, “Fabrication of Photonic Quantum Ring Laser using Chemically Assisted Ion Beam Etching”, J. of Vac. Sci. &Technol. B, Vol.19(4), , pp.1334-1338 (2001)

39.  J. G. Lee, T. K. Oh, B. Kim, and B. K. Kang, “Emitter Structure of Power Heterojunction Bipolar Transistor for Enhancement of Thermal Stability”, Solid-State Electronics, 45(1), 2001

38.  B. K. Kang, H. J. Yoo, M. K. Mheen, H. J. Kwon, and Y. H. Kim, “Nonlinearity compensation circuit for voltage-controlled oscillator operating in linear frequency sweep mode”, IEEE Microwave and Guided Wave letters, 10(12), 537-539, 2000

37.  C. G. Ahn, J. H. Kim, Y. K. Kim, Y. H. Lee, and B. K. Kang, “Effects of hydrogen and deuterium annealing on plasma process induced damages”, Jpn. J. Appl. Phys., 39(4B), 2030-2034, 2000

36.  J. C. Park, J. K. Lee, and B. K. Kang, “Properties of inductively coupled plasma source with helical coil”, IEEE Trans. on Plasma Science, 28(2), 403-413, 2000

35.  K. H. Park, B. K. Kang, M. Yoon, and J. H. Lim, “Rotating Coil Method for the Measurement of Deflecting Magnetic Fields in Cathode-Ray Tube”, Sensors and Actuators A, 86(3), 159-164, 2000

34.  M.S. Hur, J.K. Lee, and B.K. Kang, “New chaotic patterns in pulsed discharges”, Phys. Lett. A, 276(5-6), 286-290, 2000

33.  B.K. Kang, H.S. Kang, C.G. Ahn, and Y.K. Kwon, “Effect of high temperature annealing on deep levels in thin silicon-on-insulator layer separated by implanted oxygen”, J. Electrochem. Soc., 146(9), 3489-3493, 1999

32.  C.G. Ahn, H.S. Kang, Y.K. Kwon, S.M. Lee, B.R. Ryum, and B.K. Kang, “Oxidation-induced traps near the SiO2/SiGe interface”, J. Appl. Phys., 86(3), 1542-1547, 1999

31.  C.H. Shon, J.S. Park, B.K. Kang, and J.K. Lee, “Kinetic and steady-state properties of magnetron sputter with three-dimensional magnetic field”, Jpn. J. Appl. Phys., 38(7B), 4440-4449, 1999

30.  김홍주, 최준영, 박병현, 이진수, 강봉구, “후판제품창고 자동화 시스템의 연구개발”, 전자공학회지, 26(3), 264-271, 1999

29.  B.K. Kang, J.E. Milburn, Y.S. Kim, M. Yoon, K.H. Park, and D.E. Kim, “Reduction of ripple fields in a DC magnet using an auxiliary winding”, Nucl. Instr. and Meth. in Phys. Res., 417(2-3), 450-456, 1998

28.  B.K. Kang, S.D. Lee, and J.S. Lee,”Magnetic flux sensors for thick steel plate control”, Sensors &Actuators: A. Physical, 65, 203-208, 1998

27.  C.G. Ahn, H.S. Kang, Y.K. Kwon, and B.K. Kang, “Effects of segregated Ge on electrical properties of SiO2/SiGe interface”, Jpn. J. Appl. Phys., 37(3B), 1316-1319, 1998

26.  H.S. Kang, C.G. Ahn, B.K. Kang, and Y.K. Kwon, “Method for measuring deep levels in thin silicon-on-insulator layer without any interface effects”, J. of Electrochem. Soc., 145(10), 3581-3585, 1998

25.  B.K. Kang and J.E. Milburn, “Scaling law for diffused magnetic field in an eddy current passive septum magnet”, Nucl. Instr. and Meth. A, 385, 6-12, 1997

24.  J.C. Park and B.K. Kang, “Impedance model of helical resonator discharge”, IEEE Trans. on Plasma Science, 25(6), 1398-1405, 1997

23.  J.C. Park and B.K. Kang, “Reactor modeling of magnetically enhanced capacitive RF discharge”, IEEE Trans. on Plasma Science, 25(3), 499-506, 1997

22.  S.K. Lee, S.M. Choi, C.G. Ahn, W.J. Chung, Y.K. Kwon, B.K. Kang, and O.H. Kim, “Low temperature fabrication of CMOS TFT”, Jpn. J. Appl. Phys., 36(3B), 1389-1393, 1997

21.  S.K.Lee, H.G.Kim, W.J.Chung, B.K.Kang, and O.H.Kim, “Febrication of p-channel MOSFETs in RTCVD polycrystalline silicon germanium films”, Jpn. J. Appl. Phys., 35(2B), p. 919, 1996

20.  정욱진,권영규,배영호,김광일,강봉구,손병기, “RTCVD법으로 성장한 SixGel-x 에피막의 특성”, 센서학회지, 1996

19.  정욱진,권영규,배영호,김광일,강봉구,손병기, “RTCVD법으로 성장한 실리콘 에피막의 특성”, 센서학회지, 제5권, 제1호, pp. 63~70, 1996

18.  Y.H. Jeong, K.H. Choi, S.K. Jo, and B.K. Kang, “Effects of sulfide passivation on the performance of GaAs P3N5 MISFETs with photo-CVD grown gate insulators”, Jpn. J. Appl. Phys., 34(2B), 209, 1995

17.  김동언, John Milburn, 강봉구, 구양모, “Pohang Light Source용 전자석의 설계”, 한국자기학회지, 제5권 제1호, 61, 1995

16.  김성우, 박성수, 박종철, 김택승, 강봉구, 권오대, “반사형 InGaAs MQW SEED 소자의 제작 및 특성”, 전자공학회 논문지, 제 31권 A편 11호, 1511, 1994

15.  M.S. Chung, H.R. Kim, J.E. Lee, B.K. Kang, and B.M. Kim, “Via hole process for GaAs MMICs using two-step dry etching”, J. of Vac. Sci. &Technol., B11(2), 159, 1993

14.  김택무, 이승원, 추광욱, 김석태, 정문식, 김성우, 권오대, 강봉구, “16X8 반사형 S-SEED 어레이 제작 및 특성”, 전자공학회 논문지, 제 30권 A편 10호, 789, 1993

13.  정문식, 김흥락, 이지은, 김범만, 강봉구, “2단계 건식식각에 의한 GaAs Via-hole 형성공정”, 전자공학회 논문지, 제 30권 A편 1호, 17, 1993

12.  강봉구, 박기현, 윤종렬, 구양모, “방사광 가속기용 2극 전자석 특성측정 및 보정”, 한국자기학회지, 제 2권 제 2호, 163, 1992

11.  김병구, 이승원, 김택무, 추광욱, 정문식, 정윤권, 권오대, 강봉구, “투과형 Diode-Biased SEED 소자의 제작 및 특성”, 전자공학회 논문지, 제 29권 A편 6호, 496, 1992

10.  정윤권, 정문식, 김흥락, 권영규, 강봉구, “Remote PECVD 산화막의 증착특성 및 박막특성 연구”, 전자공학회 논문지, 제 29권 A편 8호, 674, 1992

9.   김흥락, 서영석, 양승주, 박성호, 김범만, 강봉구, 우종천, “HEMT 소자 제작을 위한 GaAs/AlGaAs 층의 선택적 건식식각”, 전자공학회 논문지, 제 28권 A편 11호, 902, 1991

8.   B.K. Kang, S.H. Park, and Y.J. Jeon, “Design parameter analysis for a planar type reactive ion etcher”, J. of KITE, 26, 1658, 1989

7.   H. -H. Park, B.K. Kang, E.S. Nam, Y.T. Lee, J.H. Kim, and O’d. Kwon, “Zn Diffusion Enhancement of Interdiffusion in a GaInAsP-InP Hetero-Structure”, Appl. Phys. Lett., 55(17), 1768, 1989

6.   H.-H Park, K. Lee, E.S. Nam, Y.T. Lee, J.H. Kim, B.K. Kang, and O’D. Kwon, “Impurity diffusion enhancement of interdiffusion in GaInAsP heterostructures lattice matched to GaAs and InP”, J. of Korean Physical Soc., 22, 435, 1989

5.   Y.T. Kim, C.H. Jun, K.R. Jung, B.K. Kang, B.W. Kim, and D.S. Ma, “Photo-induced chemical vapor deposition of SiO2 thin film by direct excitation process”, J. of KITE, 26, 1025, 1989

4.   B.K. Kang, M.A. Lieberman, and A.K. Sen, “Axial Feedback Stabilization of Flute Modes for Mirror Machines, B.K. Kang, M.A. Lieberman, and A.K. Sen, IEEE Trans. on Plasma Science 16, 27(1988)”, IEEE Trans. on Plasma Sci., 16, 17, 1988

3.   B.K. Kang, A.J. Lichtenberg, and W.M. Nevins, “Resistive effects on the rigid mode ballooning instability”, Phys. Fluids, 30, 1416, 1987

2.   H.D. Price, N.M.P. Benjamin, B.K. Kang, A.J. Lichtenberg, and M.A. Lieberman, “A study of high-beta ballooning modes”, Phys. Fluids, 28, 392, 1986

1.   R.A. Close, B.K. Kang, A.J. Lichtenberg, M.A. Lieberman, and H. Meuth, “Experimental observation of stabilization of an axisymmetric mirror at high-beta with a nearby wall”, Phys. Fluids, 29, 3892, 1986